【vfp精品源码栏目提醒】:以下是网学会员为您推荐的vfp精品源码-【精品】齿轮套件塑料模具设计与制作 - 大学课件,希望本篇文章对您学习有所帮助。
本设计来自:我要毕业设计网 http://www.bysj520.com在毕业设计网
注册后联系客服均可获赠您要求的毕业设计资料客服 QQ:8191040说明:本
软件/论文系有偿阅读、使用,完整 CAD 图纸或
源代码请联系客服购买全国最全毕业设计,详细目录请加 QQ8191040 索取模具毕业设计(注塑模,冲压模) ,计算机毕业设计(ASP ASP.
NET C
Delphi JAVA
JSP PB VC
VBVFP 等)机械
毕业设计,电子信息类毕业设计,土木路桥毕业设计等等7 万余篇本科硕士论文,
工商管理毕业论文
汉语言文学毕业论文 国际贸易学毕业论文
经济管理毕业论文
会计学论文 教育类毕业论文等塑料模毕业设计部分目录 http://www.bysj520.com/soft/show.aspid6冲压模毕业设计部分目录 http://www.bysj520.com/soft/show.aspid17机械毕业设计部分目录 http://www.bysj520.com/soft/show.aspid18
计算机毕业设计部分目录 http://www.bysj520.com/soft/show.aspid19电子信息设计部分目录 http://www.bysj520.com/soft/show.aspid20 塑料模具(齿轮套件)的
设计 摘 要: 聚酰胺(PA)的塑料齿轮套件,设计一套成型此零件的塑料注射模具。
通过对齿轮套件的几何形状、使用要求和材料性能的分析,确定了模具采用三板点浇口双型腔结构,每个型腔设置三个浇点,使制品的物理性能得到保证,每个浇点用拉料杆拉断,由脱料板脱下料头。
此模具选定以 XS-ZY-125 型注射机作模具成行机,采用了斜导柱侧向抽芯机构。
并且具有三次分型,分别以限位板及分型阻力悬殊等进行分型制品中间的凹部以斜导柱、侧型芯结构成型,最终由顶管将制品顶下。
合模时,顶出系统由复位杆进行复位。
关 键 词: 注射模 PA 三板点浇口 一模两腔 XS-ZY-125 注射机 斜导柱侧向抽芯, 三次分型 顶管顶出 复位杆复位 Plastic mold tooth wheel cover design Abstract: Gathers the amide PA plastic tooth wheel cover designs a set totake shape this components plastic injection mold. Through the counter gear set ofgeometry shape the operation requirements and the material performance analysishad determined the mold uses the sampan runner double die space structure each diespace establishes three pouring spots enable the product the physical performance toobtain the guarantee each pouring with pulls the material pole abruption by escapesthe yard lumber to take off the remnants. This mold designated makes the mold by theXS-ZY-125 injection machine to form a line machine used the slanting guide pillarlateral to pull out the core organization. And has three minutes respectively disparateand so on carries on minute product middle concave by the spacing board and aminute thickness drag by the slanting guide pillar the side core structure formationfinally goes against by the top pipe the product. When gathers the mold goes againstthe system to carry on the replacement by the release link. Key
words: Injection mold PA a sampan runner mold two cavity theXS-ZY-125 injection machine the slanting guide pillar lateral pulls out the corethree minutes go against the crown to leave the release link to reposition 目 录前言摘要1、了解塑件几何形状及塑料材料………………………………………………(1)2、注射机的选用…………………………………………………………………(2) 2.1 按外型结构特征分类……………………………………………………(2) 2.2 按塑化方式分类…………………………………………………………(2) 2.3 分析制品结构、尺寸精度及表面质量…………………………………… 2.4 初步确定注射机…………………………………………………………3、确定型腔数及位置布局方案…………………………………………………(4) 3.1 型腔数的确定……………………………………………………………(4) 3.2 型腔布局
方案……………………………………………………………(5)4、确定模具结构方案……………………………………………………………(5) 4.1 确定分型面………………………………………………………………(5) 4.2 确定模架组合形式………………………………………………………(6) 4.3 浇注
系统设计……………………………………………………………(7) 4.4 成形零部件的设计……………………………………………………(10) 4.5 注射模结构零部件设计………………………………………………(16) 5、