1. the time series files applied in .bnd file have no common period
这个是在validation messages中提示的,意思是说simulation中开始和结束时间设置与给定的时间序列不一致。检查下吧!否则会出现 error no385.如果确定没错误,但run parameters仍然是黄色的,不防无视之,点start。你会发现变成绿色了。
2. "Error No 25: At the h-point (location) the water depth greater than 4 times max. depth".
Why does this happen and what can be done to overcome this problem?
这个错误是初学者经常遇到的。意思是某点的计算水深远远大于河堤高程。产生原因 是模型不稳定,计算发散。解决方法 :a:减小时间步长。b:中间内插断面,
3. Warning No 65: In river xx : 7064 meter there is a difference in the bed level of the rivers meeting at the intersection.The lowest bed level (21.054 meter) is found in river BRANCH25 at chainage 0.000 meter. The highest level (21.088 meter) is found in river yy at chainage 706 meter. A difference in bed level for the rivers meeting may cause mass errors and instabilities especially if low flow is simulated.
此waring在mike计算中经常出现。我的模型第一次运行时,出现了无数个。当时冷汗…..大意是两个河道连接的地方,河底高程不同。当然,开始学mike的时候 有人告诉我,其中的waring可以忽略。但老师检查的时候出现这么多,毕竟不是什么好事。这个原因是mike默认两个河道是“无缝对接”,实际中应该差不多也是这样的。但由于选取桩号的点不同,导致河底高程有差。我的方法是在支流与主干衔接的地方,内插一断面,此断面的最低点与连接处主河道的最低点高程相同。
4.Warning No 47: At the h-point:(location )the water level has fallen below the bottom of the slot 4 times.
大意是此处的水位计算值小于河底高程。解决方法同 error no25.另外,还有某老师告诉我,可以把此处断面的宽度缩小一点点,使得断面显得高而窄。不会影响计算结果。但我试过后 ,没效果,尴尬。原因不详。
5.计算过程中出现“ floating point overflow”
这个比较麻烦,意思是模型太……..太发散了。超出
计算机的计算范围。解决方法:认真检查下各个文件。实在检查不出错误 就重新做个模型吧。我当初就是因为删了河网中的一条河道,出现了这个。而后,经过无数次改正无效后,花了几天时间重做的模型。难啊!
6. Error No 415: Networkfile: E:\mike11\C:\Documents and Settings\桌面\flood sim6g.nwk11 not found.或者导入地图文件时出现 application programmer error invalid pfshandle(cpfsdata)
呵呵 这个错误很多刚刚开始做模型的人可能遇到。就是mike要求保存的文件路径中不能有中文。
7. It is not possible to establish stead
y state solution after 100 iterations
这个是由于状态设置出现的问题。可能原因是simulation中 initial contion 选择了steady state 。这个要求初始和边界条件的匹配要合适。可以选择parameter file 试试,这个没有什么要求,计算结果不受影响。
8. The following timeseries ends too early for the applied simulation period:End time:
这个是你设定的模拟时段比给定的时间序列的时间要长。认真检查下吧。
9. 绘制河网时,只能在网格的交点上绘点。而且是竖直或水平的。不能倾斜。
在河网操作界面上,选上方的setting菜单中的network setting,在这里面network data中的snap to grid中的勾去掉就可以了
10. 如果边界条件设置成Q-H,可能出现outside the range of Q/H relation in the Boundary file.
这是计算出的水位超出了给定的范围,Mike运算时不会对边界条件进行外推,所以,如果出现这个error,给定一个极值吧。即河底水位-流量0.。。如果是